Cycling

Unless you're running tubeless (and even if you are), it's a good idea to keep a spare tube or two around, so you can change a tire quickly and reliably, then get back to riding. Continental's Schrader valve tube has you covered. - 40mm Schrader valve

Single presta tube for a 27.5-inch/650B tire. - 27.5 x 1.75-2.50 - 42mm Presta valve

Continental bicycle tubes are made of seamless butyl rubber and are individually tested for top quality. - 42mm valve length

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Tube 29-inch Schrader Valve

Continental tubes are made of seamless butyl rubber and are individually tested for top quality. 42mm valve: 95 grams 60mm valve: 100 grams

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Continental tubes are made of seamless butyl rubber and are individually tested for top quality.

Continental Cross Tubes are made of seamless butyl rubber and are individually tested for top quality. They're also heavier duty than standard tubes and perfect for the rough-and-tumble world that is cyclocross. - 48mm valve: 160 grams - 60mm valve: 165 grams

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

Continental's Easy Tape Rim Strips are 20mm wide and are made of a tough, elastic and waterproof, non-adhesive nylon. This makes they quick and easy to install. Just stretch them over your rims and let them snap in place! Each box contain a pair of rim strips.

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Customize and optimize the shoe/pedal interface. - Refine the interface between the shoe tread and pedal body - Four (4) contact sleeves - 1mm thickness

Flexible Versatite™ mount for Dash, Zot, Dart, Hotrod, Hotshot Micro 2W, Hotshot Pro 200 (flexible mount version; not for Hotshot Pro 200C) systems. Compatible with most handlebars, seat posts, and seat stays including aero styles.

Mount your Cygolite bicycle headlight to a variety of GoPro compatible interfaces and third-party mounting options that are compatible with the GoPro interface. - Compatible with Ranger, Expilion, Metro, and Streak series - Includes adapter piece only

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

- Designed to stabilize 15g spokes in most hub flanges - 1000-pack

The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - 32 nipples weigh approximately 30 grams

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Star Ratchet Spring

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Driver Spring - Ratchet EXP

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Spacer Sleeve - 10.1mm, for 3-pawl

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Spacer Sleeve - 15.4mm, for ratchet

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately