BMX

The Gyro G3 upper top plate is designed for use with the G3 detangler.

- Sold in pairs. - Allen wrench included.

Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.

Odyssey's Air Supply tubes are specifically sized to fit modern BMX tires, and they are manufactured with a stronger emphasis on quality versus simply chasing the lowest possible price. On average, the Air Supply BMX tube retains air significantly longer than others currently available on the market. This is down to both the rubber that is used, and because of strict quality control during manufacturing. It is normal to assume that a “tube is a tube,” but a higher quality tube will always last longer than a cheap tube during comparable everyday use.

When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.

The Graduate sleeve is the replacement sleeve for the Graduate peg that's made from long lasting, fast sliding plastic. - Sold singly

Compatible cable for M2 Monolever.

- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.

- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)

The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.

- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.

In addition to updating Aaron’s tire, Odyssey also wanted to update his signature grip. The updated “Boss” grip features a low profile block pattern which will match his tire, and comes in at 158mm. These will feel similar to his original grip, but improved and with all new styling.

Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.

- Press fit designed to work the hub's non-drive side collar.

The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing. (2.9 oz)

Tom Dugan’s signature grip features a timeless coil pattern, along with a feather design across the heavy wear areas. By using two molds you’ll notice feather angle symmetry once they’re installed. Par Ends included.

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.

This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length.

As the name implies, this new version can be easily adjusted to cover 3 different lengths by utilizing the cable’s unique straddle interface connection. This tool-free feature allows the Adjustable Quik Slic Kable to be a one-size-fits-all cable for virtually every braking configuration. FEATURES - Adjustable hanger slot allows upper cable to rotate for optimum alignment. - The integrated hanger and straddle cable creates direct routing to brake arms with no bends or twists to reduce flex. - Linear K-Shield mesh housing offers higher compression rate and lighter weight than standard steel mesh. - All Odyssey Linear cables are offered with the K-Shield housing. - Specially designed and machined Volcano ferrules prevent premature housing blowout. Velcro strap included. SPECS - Housing length: 995mm - Frame requirements: Slotted cable stop and guides. 245mm (+/-3) distance from center brake boss to the front of the cable stop is recommended. - Brake requirements: Open-ended U-brake arms. - Works with most brake levers. - Velcro strap included.

One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite

For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.

- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)

Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable.

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield brake drops the two ordinary (and confusing) brake springs and replaces them with one central spring that applies the same force to each arm, requiring no additional adjustment. This makes assembly incredibly easy–just bolt it on and go. The brake arms are designed to maximize stiffness and save weight without adding excessive cost. By die-casting the arms and using shared tooling to make each side, the Springfield meets all of the original design goals, resulting in a very powerful and affordable brake.

The 4.5-inch peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - Sold individually - 14mm with 3/8” adapters only - Replacement sleeves sold separately - 4.5" (length) x 1.5" (outer diameter) - 4.5 oz (9 oz for a pair)

This plastic peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - 1.5-inch outer diameter - 14mm with 3/8-inch adapter - Sold individually - Weight: 7.6oz - Replacement sleeves sold separately

- Made to fit crank spindles and press-fit Mid BB frames. - Simple and easy to install. - Includes an assortment of spacers to optimize chainline and crank clearance. - Odyssey 6061-T6 aluminum dust spacer included.

The Grandstand pedal features a unique slim profile, a wide platform and a comfortable concave that feels exceptional as soon as you set foot on it. All of Odyssey's pro riders have been after them since the first samples came in. The pedal features a unique bearing configuration that allows a big spindle to be paired with a slim pedal body. - Genuinely Thin Body. - 17mm at center with uninterrupted dual concave. - Foot-sized 105mm wide. - Full Size 14mm heat-treated axle with 17mm wrench flats and 6mm broach. - 8 oversize plastic pins per side. - 9/16” only.

Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.