Tools

Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.

Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.

A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf

A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.

Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.

Park's Cyclone Chain Scrubber is made of durable materials throughout and features an extra-large solvent reservoir, a series of rotating brushes, and a two-step cleaning process to get chains really clean without removal. There's even a strong magnet that draws metal particles scrubbed from the links to the bottom of the reservoir, preventing redistribution. And, the Cyclone's large handle makes it easy to hold and fill.

The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)

Park's Hex Wrench Set includes the most-needed Allens (4, 5 and 6mm), plus a Phillips and flathead screwdriver, all in one convenient fold-up unit. The tool tips are chamfered for a positive grip and the one-piece fiber-reinforced-resin handle is light, comfortable, slip resistant and 40% stronger than steel.

The Handlebar Holder prevents the handlebars and front wheel from swinging to the side and banging into the frame when your bike is mounted in a repair stand. It fits handlebars up to 32mm and all frame tubes up to 50mm in diameter, so it works on almost any road or mountain bike and is sure to make every repair easier.

Get those heads sealing like new and reduce compressor energy waste with Park Tool's Head Seal Kit. This kit will help get rid of that hissing sound you've been hearing when it has been too long since servicing your Park Tool INF-1 or INF-2 shop inflator. Kit includes: - 1 #1586 Presta Seal - 1 #1588 Schrader Seal - 2 #1576-2 O-rings for Shuttle-valve - 1 #1682-2 O-ring for INF-1 and INF-2 Head Adaptors

Park's versatile Headset Wrench is constructed from hardened, laser-etched steel for the maximum in durability and precision. The HCW-15 is a dual sided wrench that features a 32mm opening on one end and a 36mm opening on the other.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable. Includes the following magnetic 1/4" bits: - 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex - T25 Torx-compatible - #2 Philips cross tip - Bit holder includes empty spaces for 2 extra bits

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

Park Tool's Replacement Chain Tool Pin fits Park Tool's CT-6, CT-6.2, and CT-6.3 Chain Tools (each sold separately). • Made from hardened alloy tool steel • NOTE: The 985-1 will also push out the chain rivet completely from the chain side plate.

Park's Pin Spanners are designed for maximum usefulness and versatility at the best value. Tough high-carbon tool steel is used to ensure long life and the handles are vinyl coated for a great grip and color-coded for easy identification. The green-handled SPA-1 is used to turn the adjustable bottom-bracket cup found on most 3-piece cranksets.

Park's Screw-Type Chain Tool is the ideal shop tool for easy and reliable chain maintenance and repair. The sliding shelf makes it compatible with 1/8th-inch chains and all 3/32nd-inch chains, from 5- to 11-speed. It's made from investment-cast tool steel and has long vinyl-coated handles and fine threading for easy chain pin removal. It also includes a stiff-link loosener and comes with an extra pin.

Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.

Because even your super-fast Mavic wheels will eventually need truing, Park designed the Spoke Wrench For Mavic Wheel Systems. This comfortable, vinyl dipped, two-sided spoke wrench is designed to easily access Mavic fittings. Plus, it fits both Mavic 9mm threaded eyelets and 5.65mm integrated nipples.

Professional quality T-Handle star-shaped wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions

Precision measurement awaits with Park's Tape Measure. This small and handy tool boasts a tough, composite housing, as well as both Metric and English readings of up to 3.65 meters/12 feet.

Park's Valve Core Tool is great for tightening, removing and installing Schrader and Presta valve cores (the cores are inside the valve), and also Presta valve extenders that have 5mm wrench flats. It's a handy tool to save a tube when all that's wrong is a broken valve, and it also lets you remove valves to easily insert sealant.

Park Tool's professional-quality Snap Ring pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl dipped grips. The RP-1 has .9mm tips on straight blades for small, internal snap rings. The tips open from 22mm to 0 (tips touching).

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-2 has 1.3mm tips on bent nose blades for medium, internal snap rings. The tips of the RP-2 open from 22mm down to 2mm (center to center).

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-4 has 1.7mm tips on bent nose blades for larger, internal snap rings. The tips open from 21mm down to 2mm (center to center).

Professional quality ring plier made from forged, heat-treated cro-moly steel with a return spring and vinyl dipped grips. The RP-5 has 1.7mm tips on straight blades for small, internal snap rings. The tips open from 22mm to 0 (tips touching).